When applied at 100 sq/ft per gallon, Norklad 100-UV willself-levelto a glasslike surface. Full cure (heavy traffic): 2-7 days @ 70 degrees F Norklad 100-M is a two component 100% solids epoxy broadcast coat that can be filled with decorative chips and colored sand mixtures to provide an infinite array of color schemes or patterns. This gives it the name '100% solids.' Always remember that colder temperatures will require more cure time for the product before recoating or topcoating can commence. The material in the transfer pail is now ready to be applied on the primed substrate. However, the material can also be applied by a suitable serrated squeegee and then back rolled as long as the appropriate thickness recommendations are maintained. When to use Norklad 100-UV: 100% solidsis recommended for warehouses, kitchens, restrooms, and other areas where either a high build clear product is needed or where a decorative filled floor is desired. Always remember that colder temperatures will require more cure time for the product before recoating or topcoating can commence. COVERAGE PER GALLON: 90-100 square feet per gallon @ 16-18 mils 100% solids epoxy is the only epoxy that can be used for metallic epoxy floors (pictured above). i. APPLICATION TEMPERATURE: 55-90 degrees. *For best results, apply with a nap roller and/or squeegee.

VOLATILE ORGANIC CONTENT: Zero pounds per gallon It is 100% solids therefore has low odor, no flammability, and is self-leveling. We recommend topcoating with a urethane product to assist in UV-resistance. If concrete conditions or over aggressive mixing causes air entrapment, then an air release roller tool should be used prior to the coating tacking off to remove the air entrapped in the coating. All rights reserved | Privacy Policy | Terms of Use. (1 gal of part a (resin) and half gallon of part b (hardener). This is a product guide to help you decide which epoxy is best for you. After the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. It is 100% solids therefore has low odor, no flammability, and is self-leveling. It is best to let the floor remain dry for the full cure cycle. We recommend topcoating with a urethane product to assist in UV-resistance. APPLICATION TEMPERATURE: 55-90 degrees F, pot life 1 1/2 gallon volume .. 20-30 minutes @ 70 Ftack free (dry to touch)6-8 hours @ 70 Frecoat or topcoat.. 10-16 hours @ 70Flight foot traffic..14-18 hours @ 70Ffull cure (heavy traffic) 2-7 days @ 70F, CHEMICAL RESISTANCE:REAGENT RATINGbutanol Cxylene C1, 1, 1 trichloroethane BMEK Amethanol Aethyl alcohol Cskydrol B10% sodium hydroxide E50% sodium hydroxide D10% sulfuric acid C70% sulfuric acid A10% HC1 (aq) C5% acetic acid B. SIZES: Standard packages are packaged in 1.5-gal kits. If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate is dry enough to start coating. Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website. If concrete conditions or over aggressive mixing causes air entrapment, then an air release roller tool should be used prior to the coating tacking off. Then broadcast aggregate into the coating while wet. CURE SCHEDULE: We apologize for this inconvenience. COVERAGE PER GALLON: 53-130 square feet per gallon @ 12-30 mils Ideal for full broadcast terrazzo or colorchip floors. After the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. Test each cleaner in a small area, utilizing your cleaning technique. Standard packages are in pre-measured kits and should be mixed as supplied in the kit. If a primer is not used, more porous substrates may cause outgassing and possible surface defects. Light foot traffic: 14-18 hours @ 70 degrees F COLOR: Clear This category only includes cookies that ensures basic functionalities and security features of the website. If no ill effects are noted, you can continue to clean with the product and process tested. VISCOSITY: Mixed = 700-1000 cps (typical) Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. light foot traffic: 12-14 hours @ 70 degrees F SOLIDS BY WEIGHT: 100% After the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. ABRASION RESISTANCE: Taber abraser CS-17 calibrase wheel with 1000 gram total load and 500 cycles = 36 mg loss Norklad 100 can easily coat over any solvent or water based epoxies. The base coat must be 100% solids because its self leveling properties allow the pigments to blend together and settle evenly. If concrete conditions or over aggressive mixing causes air entrapment, then an air release roller tool should be used prior to the coating tacking off. When to use Norklad 100-M: 100% solids is recommended for warehouses, kitchens, restrooms, and other areas where either a high build clear product is needed or where a decorative filled floor is desired. Apply your base coat and colorchips and allow to sufficiently cure. pot life 1 1/2 gallon volume: 30-50 minutes @ 70 degrees F TOPCOAT: Urethane topcoat is recommended for added UV-Resistance if exposed to sunlight. wood uv clear deck finish stain finishes resistant exterior epoxy olympic defy fence semi maximum redwood siding transparent sikkens cabot Maintain temperatures and relative humidity within the recommended ranges during the application and curing process. We highly recommend that the kits not be broken down unless suitable weighing equipment is available. full cure (heavy traffic): 2-7 days @ 70 degrees F, APPLICATION TEMPERATURE: 60-90 degrees F with relative humidity below 85%, SOLIDS BY WEIGHT: 100% (+/- 1%) Tack free (dry to touch): 6-8 hours @ 70 degrees F ABRASION RESISTANCE: Taber abraser CS-17 calibrase wheel with 1000 gram total load and 500 cycles = 36 mg loss Continuous storage should be between 60 and 90 degree F. Low temperatures or temperature fluctuations may cause product crystallization. 1.5 Gallon (175+ sq/ft) SURFACE PREPARATION: The most suitable surface preparation would be a fine brush blast (shot blast or diamond grind) to remove all laitance and provide a suitable profile. HARDNESS: Shore D = 81 These cookies do not store any personal information. Maintain temperatures and relative humidity within the recommended ranges during the application and curing process. Apply your basecoat and colorchips and allow to sufficiently cure. Some of our DIY customers have had great success by carefully researching and buying the proper tools, but know that if you have never installed a 100% epoxy floor before, you are taking a risk by doing so. When applied at 100 sq/ft per gallon, Norklad 100-M will self-level to a glasslike surface.

This product can be used with random chip broadcasts, full chip broadcasts, or colored quartz. They are in pre-measured kits and should be mixed as supplied in the kit. Low odor, low VOC formula is ideal for use on interior coated or bare concrete surfaces including garages, basements, workshops and more, Your email address will not be published. FLEXURAL STRENGTH: 5,400 psi @ ASTM D790 SOLIDS BY VOLUME: 100% (+/- 1%)

All dirt, foreign contaminants, oil and laitance must be removed to assure a trouble free bond to the substrate. tack free (dry to touch): 5-8 hours @ 70 degrees F Then broadcast aggregate into the coating while wet. FINISH CHARACTERISTICS: Gloss (70-95 at 60 degrees @ Erichsen glossmeter) GARDNER VARIABLE IMPACTOR: 50 inch pounds direct passed TENSILE STRENGTH: 4,800 psi @ ASTM D638 We will do our best to keep accurate stock availability online. After mixing, transfer the mixed material to another pail (the transfer pail) and again remix. Recoat or topcoat: 10-16 hours @ 70 degrees F SURFACE PREPARATION: The most suitable surface preparation would be a fine brush blast (shot blast) to remove all laitance and provide a suitable profile. COMPRESSIVE STRENGTH: 11,200 psi @ ASTM D695 COMPRESSIVE STRENGTH: 9,100 psi @ ASTM D695 1/2" X 1/2" bars After mixing, transfer the mixed material to another pail (the transfer pail) and again remix. TENSILE STRENGTH: 7,600 psi @ ASTM D638 ULTIMATE ELONGATION: 4.1% We highly recommend that the kits not be broken down unless suitable weighing equipment is available. The material in the transfer pail is now ready to be applied onto your base coat. If you are looking for colored epoxy, check out Norklad 200, which is available in 12 different colors. If used alone, it is recommended that a primer coat be used to prevent outgassing/blistering. ULTIMATE ELONGATION: 3.1% 3 Gallon (400+ sq/ft). 100% solids epoxy is considered the industry standard for high-end flooring due to the fact that it is 4x stronger than concrete and has no voc, no flammability and can be applied as thick or thin as you need it. RESTRICTIONS: Restrict the use of the floor to light traffic and non-harsh chemicals until the coating is fully cured (see technical data under full cure). Norklad 100-UV is a two component 100% solids epoxy broadcast coat that can be filled withdecorativechips and colored sand mixtures to provide an infinite array of color schemes or patterns.

FLEXURAL STRENGTH: 7,400 psi @ ASTM D790 (wait until you can no longer leave an imprint of your finger in the coating. FINISH CHARACTERISTICS: Gloss (60 to 90 @ 60 degrees @ Erichsen glossmeter) TENSILE STRENGTH: 7,600 psi @ ASTM D638 ADHESION: 350 psi @ elcometer (concrete failure, no delamination) TOPCOAT: Urethane topcoat is recommended for added UV-Resistance if exposed to sunlight. We also use third-party cookies that help us analyze and understand how you use this website. .75 Gallon (75-100+ sq/ft) Before recoating or topcoating, check the coating to insure no epoxy blushes were developed (a whitish, greasy film or deglossing). GARDNER VARIABLE IMPACTOR: 50 inch pounds direct passed We sell 100% solids epoxy in both colored and clear. PRIMING: A suitable primer should be used before applying this product. Norklad 200 is a two component 100% solids epoxy colored coating designed for applications where a high build colorfast impact resistant floor is needed. FLOOR CLEANING: Caution! The plastic sheet testing is also a good method to determine if any hydrostatic pressure problems exist that may later cause disbonding. SOLIDS BY VOLUME: 100% There are no harmful organic vapors (VOCs) like you experience with urethane application. Improper mixing may result in product failure. PRODUCT APPLICATION: The mixed material can be applied by brush, roller or a serrated squeegee and then back rolled as long as the appropriate thickness recommendations are maintained. All dirt, foreign contaminants, oil and laitance must be removed to assure a trouble free bond to the substrate. This drawback of 100% solids epoxy can also be a positive; many professionals appreciate the fast potlife of 100% solids because it makes jobs faster and more efficient. Orders placed over the next few months may be delayed or will be refunded. PRODUCT STORAGE: Store product at normal room temperature. (wait until you can no longer leave an imprint of your finger in the coating.) But opting out of some of these cookies may affect your browsing experience. NOTE: extensive chemical resistance information is available through your sales representative. A properly installed 100% solids floor will last for 20 years or more.However, 100% solids epoxy has an extremely short potlife and cure time of only 30 minutes. ABRASION RESISTANCE: Taber abraser CS-17 calibrase wheel with 1000 gram total load and 500 cycles = 32 mg loss A test should be made to determine that the concrete is dry; this can be done by placing a 4'x4' plastic sheet on the substrate and taping down the edges. VISCOSITY: Mixed = 700-1000 cps (typical) PACKAGING INFORMATION 1.5 gallon kits (2.95 gallons net approximately) After mixing, transfer the mixed material to another pail (the transfer pail) and again remix. Colder temperatures will require more cure time for the product before recoating or topcoating can commence. FLEXURAL STRENGTH: 7,400 psi @ ASTM D790 Slip Resistant Floor Coating Grit Additives. Pot life - 1 1/2 gallon volume: 20-30 minutes @ 70 degrees F

RECOAT OR TOPCOATING: If you opt to recoat or topcoat this product, you must first be sure that the coating has tacked off before recoating. This website uses cookies to improve your experience while you navigate through the website. Maintain temperatures and relative humidity within the recommended ranges during the application and curing process. If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate is dry enough to start coating.

If you are looking for a basic clear coat, look no further than Norklad 100 M. If you are looking for a UV resistant clear coat, upgrade to Norklad 100 UV. COVERAGE PER GALLON: 90-100 square feet per gallon @ 16-18 mils ADHESION: 450 psi @ elcometer (concrete failure, no delamination) Required fields are marked *, This website uses cookies for the best browsing experience. Standard packages are packaged in 1.5-gal kits. This product can be used with random chip broadcasts, full chip broadcasts, or colored quartz. COMPRESSIVE STRENGTH: 11,200 psi @ ASTM D695 SOLIDS BY WEIGHT: 100% It has a very fast pot life (30 minutes) once it's mixed with the converter. RECOMMENDED FILM THICKNESS: 16-18 mils Norklad 100-M can easily coat over any solvent or waterborne epoxies. Before recoating or topcoating, check the coating to insure no epoxy blushes were developed (a whitish, greasy film or deglossing). Once you get the product out of your mixing bucket it takes much longer for it to tack off. SOLIDS BY VOLUME: 100% ULTIMATE ELONGATION: 4.1%

It's recommend to squeegee this product out and apply 100-125 sq/ft per gallon (approx.14-16 mils) and back roll it with a shed-resistant roller to even it out. It can be used as durable color coat for for maximum durability or as a colored base coat for color chip broadcasts. HARDNESS: Shore D = 81 A test should be made to determine that the concrete is dry; this can be done by placing a 4'x4' plastic sheet on the substrate and taping down the edges. If a blush is present, it must be removed prior to topcoating or recoating. However, all previous coats should be deglossed to insure a trouble free bond prior to application of recoats or topcoats. FINISH CHARACTERISTICS: Gloss (60 to 90 @ 60 degrees @ Erichsen glossmeter) VISCOSITY: Mixed = 1300-2300 cps (typical, most colors) If you are ready to purchase, head to our webstore. Ideal for full broadcast terrazzo or colorchip floors. SURFACE PREPARATION: The most suitable surface preparation would be a fine brush blast (shot blast or diamond grind) to remove all laitance and provide a suitable profile. PRODUCT APPLICATION: The mixed material can be applied by brush, roller or a serrated squeegee and then back rolled as long as the appropriate thickness recommendations are maintained. Before recoating or topcoating, check for epoxy blushes (a whitish, greasy film or deglossing). If you are interested in a this kind of finish, check out our metallic epoxy floor kit page that includes complete kits and application instructions. The plastic sheet testing is also a good method to determine if any hydrostatic pressure problems exist that may later cause disbonding. Improper mixing may result in product failure. VOLATILE ORGANIC CONTENT: Nearly zero pounds per gallon 100% solids epoxy does not have water or solvents that evaporate while curing; it retains 100% of its thickness and body after cure. By continuing to use this site, you accept our, 1 gal Rust-Oleum Brands 292514 Clear EpoxyShield Premium Clear Coating, polyurethane has many advantages over epoxy, home improvement centers and paint stores harm more than help, How to Fix or Prevent a Rough Textured Color Flake Coating, G-Floor Garage Mats Review | We Reveal The Good And The Bad, The Poor Reviews and Ruined Expectations of Garage Floor Coatings, Street Outlaws Ryan Martin Applies Nohr-S Polyurea Coating System to His New Shop Floor, How to Eliminate Pet Urine Odors from Concrete and Basements, How To Prep and Recoat an Older Epoxy Floor for a New Coat, What You Should Know About Interlocking Garage Floor Tiles, Why the Best DIY Floor Coating Kits are Single-Part Polyurea, Tips for Filling Contraction and Expansion Joints, How to Easily Repair Your Pitted and Spalled Concrete, Rust Bullet, A Long Lasting Garage Floor Paint has Arrived. They are in pre-measured kits and should be mixed as supplied in the kit. RECOAT OR TOPCOATING: If you opt to recoat or topcoat this product, you must first be sure that the coating has tacked off before recoating. We sell many types of 100% solids epoxy. A test should be made to determine that the concrete is dry; this can be done by placing a 4X4 plastic sheet on the substrate and taping down the edges. VOLATILE ORGANIC CONTENT: Zero pounds per gallon Some cleaners may affect the color of the floor installed. COLORS: Light Gray, Medium Gray, Charcoal, Off White, Beige, Tan, Wheat, Taupe, Tile Red, Royal Blue, Steel Blue, Black, White If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate is dry enough to start coating. RECOMMENDED FILM THICKNESS: 16-18 mils Rating key: A - not recommended, B - 2 hour term splash spill, C - 8 hour term splash spill, D - 72 hour immersion, E - long term immersion.

Sitemap 16