To test if your RO system is shutting down normally, please follow the steps below. Install the RO in a sheltered environment, avoid exposure to hot and cold weather or under direct sunlight. membrane osmosis removes gpd compatible contaminants APEC Water RO-90 - 90 GPD Ultra Safe Reverse Osmosis Drinking Water Filter System - Use Manual - Use Guide PDF. Close up the housings. Slip the plastic wrench onto the 1st housing. Feed water temperature: 40 100 F (4-37 C), Do not connect this unit to hot water source. Open housing: Have the RO standing upright.

Turn OFF tank ball-valve. Once the drain saddle is secured, push 1/4 black drain tubing into the Quick Connect fitting on the saddle. 9B (Page 12). Note: For stainless steel sinks, we recommend reversing the black locating washer so the flat end is facing upwards for proper installation. DO NOT use a Insert on the drain tubing. Mis-aligning these two holes will block the drain water and cause membrane damage. First hand tighten the housing, then use filter wrench to fully tighten each housing. Turn on the RO faucet lever to relieve the built-up pressure inside the RO system.

Turn OFF cold water supply to RO system. If necessary, lay RO down on the floor to get a better leverage. 9C (Page 12). The RO system should shut off automatically when the tank is filled. Mounting: No need to mount the RO system on the wall. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after system. All rights reserved. Space: Make sure there is sufficient space under the counter for installation (an area of about 17L x 6W x 18H for the system, 11D x 18H for tank).

This reverse osmosis system contains a replaceable treatment component critical for effective re- duction of total dissolved solids. APEC Water Systems - Water Filtration Systems.

When the RO fails to shut off after tank is filled, drain water will keep running down the drain depleting the pre-filters, the membrane, and may lead to higher water bills. Make sure each housing has a black O-ring in the threaded groves. Next, align and install the drain saddle clip with the tubing connection port onto the black sponge. The drain saddle assembly should be installed above the trap and on the vertical or horizon- tal tailpiece.

apec roes uv cartridge Feed Water: RO systems are designed to treat both hard and soft water and can handle incoming TDS levels up to 2,000 ppm. If you prefer to mount the system to the wall, please make sure it can be taken down easily for filter replacement. Use manuals file type: PDF. User manualWater Filter System forAPEC Water RO-90. Select the location of the hole and drill a 1/4 hole through one side of the drain pipe then put the self-adhesive black sponge around the hole location (See Fig. Discard 3 used filters, wash housings with mild soap, rinse off.

Attach the drain saddle to the drain pipe and tighten the two screws evenly. If the housing is too tight, use a hammer and gently tap on the wrench handle to help turn the wrench. The RO system can stand in the sink cabinet without mounting, this makes future filter change easy and convenient.

9D (Page 12). Check drain water by pulling the black drain tubing out from the drain pipe and let water flow into a good size bucket to view it. Keep tank ball valve CLOSED and Turn ON the cold water supply as well as RO faucet lever.

If your RO feeds multiple output points (icemaker, bathroom, etc), please use a manual shut off valve to shut OFF water to those lines. See Fig.14 (Page 20). If drain water stops running --> The RO is shutting off properly no additional test is needed. Copyright 2022 ManualsFile.com. Mount the faucet as shown in Fig. Make sure the tube insert is pushed all the way into the tubing Fig. This will cushion any gap between the saddle and the pipe. Do not over-tighten. Draw 3-4 glasses of water from spigot. Please let purified water run for 10-15 minutes to relieve built-up pressure inside the RO unit. 7A and 7B). This will make opening the housings easier. There is constant water pressure packed inside the RO system which blocks the drain water from backing-up into the system. The faucet handle controls the flow of purified water exiting the faucet. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts. Looking down from a top view, you should open the housing turning clockwise. Turn OFF the blue tank ball valve on top of the water storage tank clockwise 90 degrees to mimic a full tank. Turn OFF the RO faucet lever and Turn ON the tank ball valve. Connect the Clear faucet tubing directly to system output. System must be installed indoor away from possible environmental damage. So the drain water is forced-drained, not gravity-drained.

Make sure the hole on the sponge is thoroughly punched out, and is aligned to the hole on the saddle to complete the installation. Make sure to align the drain saddle hole to the drilled hole perfectly.

But if that is not feasible you can install the system anywhere where there is a cold water supply with sufficient water pressure for the chosen RO model, and an outlet to drain off the drain water from the system.

Make sure the tubing is inserted inside the faucet stem at least 1/4 deep while screwing the compression nut Fig. Put 3 new filters into their respective housings: sediment filter in stage-1, carbon block filters in stages 2 & 3.

Wait up to 10 minutes, then check to see if the drain water starts slowing down to a stop. To reduce the drainage noise, mount the drain line as low as possible above the trap, or on the horizontal tailpiece. If your faucet comes with tubing attached: If your faucet comes without tubing attached: How To Replace Stages 1, 2, 3 Pre-Filters: General Installation/Operation/Maintenance Requirements. Installation needs to comply with state and local laws and regulations. The product water shall be tested periodically to verify that system is performing satisfactorily. Input water pressure: most important factor, TDS (Total Dissolved Solids) Level Reads Higher Than Normal, There is a leak at the tank ball valve connection. The RO system is best installed under the kitchen sink. Turn the handle to horizontal position to release the water and vertically to shut off. RO will start making water to fill tank.

Sitemap 27